Wire introduction
The picture above is commonly used, and it is also a few types of hook wires that are easier to buy on the market. It’s hard to say which line is particularly good or worse. Fishermen should choose the appropriate hook line from the three perspectives. Of course, strength and abrasion resistance are the first factors we consider. Because the hook line is likely to be directly exposed to the fish mouth, especially the fish species that fishing those sharp teeth. In this link, try to guarantee more safely. Do not cause regrets of running fish because of the problems of lines and tied methods.
Ygk zylon line
, Japan’s Toyo Textiles developed high -intensity and elastic fibers, brown, up to 100, which is relatively thick.
Ygk galis sea hunter
Dark red, the line body feels hard and has good wear resistance.
Varivas SSSISTLINE
, Dark red, relatively soft, after the water is overwhelmed.
Ygk galis iso hunter
, White, feel soft.
YGK Galis Ultra
Orange yellow, double -layer fiber structure, smooth and wear -resistant outer layer.
AMIKA Gold Line
, Earth yellow, single -layer woven structure.
Other bulk weaving cables.
Basically, the materials of the hook line are all developed in Japan. Even if China is weaving and re -packaging, its original fiber is also made in Japan. If it is not a specific fiber -made hook line, it is difficult to meet the requirements of high strength and high wear resistance.
Necessary tool preparation
Single -share dual hook
▼
This binding method is very popular around the world. It is easy to learn, and it is also a kind of bonding method that saves the hook line. Another advantage of this binding method is that the upper and lower hooks have long and short. During the fall of the iron plate, the two hooks are scattered in different areas around the iron plate, which is helpful for improving the hook rate. But please do not try too soft lines, because both hooks are on the side of the iron plate. Too soft lines will cause two hooks to wrap together.
Step 1: 2-3 circles on the thumb or index finger
Step 2: The line head passes through the middle
Step 3: Look at this knot on the side, and then pass the hooks from this hole
Step 4: Put the hook into the middle
Step 5: Tighten the line head, pull as much as possible as much as possible
After throwing the line, use your left hand to touch the fishing line with a slightly sliding line wheel to avoid excessive qualifying and the generated homeline.
Step 6: The line head passes through the hook handle from the hook door, which is very important.
Step 7: From a different angle, look at the line
Step 8: The other end of the line is tied in the same way
Step 9: After putting on the thermal tube, warm up
Step 10: Successful
Step 11: The best state is tied to the iron plate.
Double -share single hook i
Although this dual -line single -hook method is not unique to Taiwan Jigmaster, because Taiwan Jigmaster enters the mainland earlier, its understanding of iron plate fishing and commonly used technology have a deeper impact on the mainland fishermen. In particular, this kind of binding method seems to be the only choice for mainland fishermen to a certain extent.
Any binding method has its advantages and disadvantages, and the binding method of this double -line single hook does have its own uniqueness. When the hook wire has a certain hardness, and the short of the iron hook is very upset, the iron plate hook hangs the iron plate during the bait process, causing the non -hook. Another advantage is that even if one line is cut off, the other line can still work even if one line is cut off. Obviously, if you use this method to tie the long line, it has weakened its advantages. Therefore, this double -line tie method is not appropriate for those who are accustomed to long -term fishermen.
Step 1: Fold the hook line
Step 2: 1-2 circles on the thumb or index finger
Step 3: Cross from the line from the middle
Step 7: After putting on the thermal tube, warm up
Step 8: Successful
Step 9: Tied to the iron plate.
Double -share single hook II
This kind of binding method is the essence, which is the same as the principle of the previous one. It can be tied to different lengths according to the habit of fishing. But this binding method also has a prerequisite to use hollow tie lines so that the cable can pass through the middle.
Step 1: Hollow hook wire folding
Step 2: Fold the wire to fold, penetrate from the middle of the hook line, wear to almost half of the distance
Step 3: Pass the other end of the hook wire through the wire, then pump the wire in it, and pass through the other end of the line from the middle of the hook wire.
Step 4: Pull out this header
Step 5: At this time, the two shares of the other side are merged into one
Step 6: 1-2 circles on the thumb or index finger
Step 7: The line head passes through the middle
Step 8: Put the hook into the middle
Step 9: The line head passes through the hook handle from the hook door
Step 10: Tighten the line head, pull as much as possible as much as possible
Step 11: After putting on the heat shrinking tube, warm up
Step 12: Successful
Step 13: Tied to the iron plate.
Four single hooks
If you pursue the strength, bitterness, and DIY beauty. Then this complicated hook method will definitely satisfy you. It is manually woven from four hollow tie lines, and the actual strength is far greater than 4 single stocks. Very line -consuming and time -consuming has also become the reason why this binding method cannot be widely promoted. But from the perspective of exploration, attempt, and pursuit of the extreme, there are reasons for its existence.
Step 1: Two hollow tie lines are folded separately. In order to explain clearly, one is line A and the other is line B.
Step 2: The wire is put into the interior from the middle part of the hollow tie line A line, and then wears it from the front. The distance is about 3-4 cm.
Step 3: Put another binding line B line into the wire, and then pull it inwardly
Step 4: In other words, this hook line B line B, passing through the hollow interior of another line A line A
Step 5: Line A and line B are in the middle part.
Step 6: Details display
Step 7: Start weaving, cross the four lines of the line, and tightly weave together
Step 8: Fixed in one position, it will help you make the line more compact
Step 9: Edited lines
Step 10: Tie the hook and put on the finished product after the heat shrinkage. The process of tied hooks is not introduced here, just like the previous.
Step 11: The exquisite and powerful invincible iron plate hook tie method
▼
▼
▼
Step 4: Put the hook into the middle
Step 5: Tighten the line head, pull as much as possible as much as possible
Step 6: The line head passes through the hook handle from the hook door, which is very important.
